Roller Veneer Dryer Feeder-manufacture,factory,supplier from China

Why suggest you to choose Shine biomass burner roller veneer dryer ? 1. The biomass burner, a patented product independently developed by our company, can directly use crushed wood waste as fuel to provide a heat source for the dryer, no need to buy steam boiler or thermal oil again . which is energy-saving and environmentally friendly, and greatly reduces the drying cost. The comprehensive drying cost for one cbm is about $10 lower than thermal oil or steam boiler. 2.

Xishuangbanna customers ordered two set  58 meters 4.5 meters wide double layer  roller veneer dryer ,which use thermal oil as fuel . They two veneer dryers were installed well and put into use successfully . they will dry the rubber veneers and welcome to visit and give suggestion. 

The Brazilian customer bought our 24m single-layer veneer drying equipment with our patented biomass burner,  the customer feedback that our equipment is very good, it can  achieve the expected output and  dried veneer moisture content is even, flat, no wrinkles.We have a professional R&D team that can design different models according to customer’s special requirement.

Since its establishment in 1999, Shine Machinery has always adhered to the development concept of continuous innovation and provided excellent solutions for customers.At present, our largest roller veneer dryer has been installed and runs smoothly in South Africa, capable of drying approximately 230 cubic meters of veneer in 24 hours.Recently, our 6-layer and 6-meter wide veneer dryer has also unveiled its mysterious veil. Currently, research and development are progressing smoothly, with an expected hourly output of around 15-18 cubic meters, which will further enhance the user experience.

Recently, our Six-deck Roller Veneer Dryer carryed on a test run, and Peruvian customer visited the testing site. At present, the R&D work is progressing smoothly, and the new generation of automatic veneer loading machine meets expectations. The new dryer will undergo a fully automated upgrade to reduce labor costs while ensuring efficient and stable drying. It is expected to produce around 15-18 cubic meters per hour.

The 58-meter-4.5-meter-wide double-deck roller veneer dryer purchased by a customer in Xishuangbanna is heated by heat-conducting oil,with high output, and the moisture content of the dried veneer is uniform.The customer has now put it into use.Very satisfied,our equipment has been affirmed by many domestic and foreign customers,we must work harder to do better,and welcome customers to visit our factory at any time.

We have extensive experience in drying rubber wood veneer. Our dryer has the advantages of low card rate and easy maintenance of equipment.Reasonable roller diameter and roller spacing not only ensure that hot air can be evenly distributed on both sides of the veneer, but also greatly reduce the occurrence of veneer jamming. At the same time, the ellipticity of the roller does not exceed 100 um, and the straightness does not exceed 500 um, which also reduces the occurrence of jamming.

The 56m 2 deck roller veneer dryer  is being installted now in Zimbabwe, this is the second set veneer drying machine from our South Africa client, who will install the third one in the next year . Shine biomass burner can use the crushed waste wood as fuel directly , which can save the drying cost for the user .  the client is very satisfied with the operation of our veneer dryers .welcome to visit the veneer dryer site to consult  . 

Shine newly installed 36m 2 deck roller veneer dryer with 4ton biomass burner was put into use last week in Xishuangbanna  .  The comprehensive operation state is very good and the user is very satisfied with it . The user is considering to buy another 48m 2 deck ones from us soon .  Thanks for the trust from our clients and welcome friends all over the world to visit our veneer drying machine. 

The veneer dryer needs to pay attention to some problems when drying wood. Before use, the heating fan should be started first, and when the drying temperature is reached, the speed regulating motor should be started. The veneer should enter from the feeding port longitudinally, the feeding should be straight, the veneer and the transmission roller should be connected at a 90-degree angle, and the veneer should be cut neatly before drying.